Intex Pool Legs Not Straight

The most common issue with Intex pool legs not being straight is that the ground underneath them is uneven. This can cause the entire pool to be out of level and lead to issues like water leaking from one side or another. To solve this issue, you will need to level the ground underneath each leg by using a shovel and/or tamping tool.

If needed, use gravel as a filler material in order to make sure it’s completely flat underneath each leg before setting up your pool. You’ll also want to double check that all four legs are even in length so they support the pool evenly and don’t create any stress points on one side or corner of the structure. Once everything is leveled properly, you should have no further problems with having Intex pool legs not being straight!

If you have recently installed an Intex pool and noticed that the legs are not straight, this is a common occurrence. This can be due to uneven ground or incorrect installation. To remedy the problem, make sure your frame is level before installing the pool liner.

Additionally, inspect each leg for any signs of damage such as cracks or bends and replace if necessary. Finally, use adjustable feet on each leg to ensure even support throughout all four corners of your pool frame. With these tips in mind, you should be able to get your Intex pool up and running with perfectly straight legs!

Intex Pool Legs Not Straight


How Do I Straighten My Intex Pool Legs?

Straightening Intex pool legs is an easy job that can be done with the right tools and some patience. To straighten your Intex pool legs: • Unscrew the leg caps from each leg of the pool.

• Place a support block under each leg to prevent sinking in soft ground. • Adjust each leg until it is level with the others, then tighten the screws firmly once you’re happy with their position. • Reattach any necessary bolts or screws and replace the caps on all four corners of the pool.

Finally, check that all four legs are secure before refilling your Intex Pool!

How Do I Make My Pool Legs Straight?

To make your pool legs straight, there are a few steps you can take:• Check the sand bed of your pool to ensure it is even and level. Use a spirit level and shovel to correct any irregularities.

• Inspect the leg anchors for rust or corrosion, replacing them if necessary. • Make sure all nuts, bolts and screws around the base of each leg are tightened securely. • If possible, use an underwater wrench to adjust any misaligned legs until they are in line with the rest of the structure.

Once these steps have been taken, your pool legs should be straight!

How Unlevel Can an Intex Pool Be?

An Intex pool can be up to 2 inches unlevel. It is important that the pool is not more than this, as it could cause damage to the structure of the pool and may also lead to instability when in use.To ensure an Intex pool is level:

• Place a 4-foot level on each side of the pool from end-to-end • Measure any dips or bumps with a tape measure • Fill any dips with sand and remove excess material from bumps

• Check again with the level until it’s perfectly flat.

How Do You Fix an Unlevel Pool Without Draining It?

To fix an unlevel pool without draining it, the following steps should be taken: •Identify the area that needs adjusting. •Remove any obstructions from around the base of the pool so you have space to work.

•Shim any low spots with a foam board and level them out. •Fill in gaps with sand or dirt, depending on how deep they are. •Use a carpenter’s level to ensure all areas are even and adjust as needed.

Once all adjustments have been made, your pool should be balanced again!

DIY – Pool Leg Repair


In conclusion, an Intex pool can be a great addition to your backyard and is relatively easy to set up. However, it’s important that the legs are straightened in order for the water to stay balanced and level. If you have noticed that your Intex pool legs are not straight, it is essential to take measures as soon as possible in order to prevent damage from occurring.

With some simple adjustments of the support posts or by adding extra weight on one side, you will be able to ensure your pool stays safe and secure for many years to come.

Home Advisor Blog

Home Advisor Blog is a reader-supported blog. This site is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to and affiliated sites.