Little Giant Pool Cover Pump Not Working

If your Little Giant Pool Cover Pump is not working, there are a few steps you can take to try and fix the issue. First, check that the power cord is securely plugged into an outlet. If it is and still not working, check to make sure the pump isn’t clogged with debris or other matter.

Additionally, inspect for any broken seals or parts on the pump itself. Another possible solution could be to replace a worn out impeller if one was found in inspection of the pump’s components. Lastly, ensure that you have enough water pressure entering into your pool cover pump so that it can operate properly when turned on again after all checks were cleared as described above.

If you’ve purchased a Little Giant pool cover pump and it’s not working, don’t despair. The first thing to do is to make sure the pump has power. Ensure that the outlet is switched on and plugged in correctly.

If everything appears okay, then check the float switch for proper operation as this could be causing an issue with the motor running. If all else fails, contact customer service or your local dealer for help with troubleshooting and getting your pump up and running again!

Little Giant Pump Impeller Not Spinning

If you have a Little Giant water pump and the impeller isn’t spinning, it could be caused by a number of issues. The most common causes are dirt or debris clogging the impeller, an electrical problem such as a blown fuse or bad switch, inadequate voltage supply to the motor, improper installation of the motor shaft or bearings, and worn out seals. If your pump has one of these issues then it’s important that you get it fixed quickly in order to prevent further damage from occurring.

Little Giant Pump Not Turning on

If your Little Giant Pump isn’t turning on, the first thing you should do is check the power supply. Make sure that all connections are secure and properly plugged in. If everything appears to be connected correctly, try resetting the breaker or plugging it into a different outlet.

You may also need to clean any debris from around the switch or control box, as this can cause an interruption in power flow. If these troubleshooting steps don’t resolve your issue, contact a professional to inspect and repair your pump.

Little Giant Pool Cover Pump Trips Breaker

A Little Giant Pool Cover Pump is a powerful and efficient tool that can help you remove water from your pool cover quickly and easily. It is designed to prevent damage to the cover caused by excess water, as well as provide a safe environment for swimmers. However, it’s important to note that this pump draws a high current when running, which may cause it to trip the breaker if not properly wired or sized correctly for your specific pool setup.

Be sure you consult with an electrician before installing one of these pumps to ensure optimal performance and safety.

Little Giant Pool Cover Pump Warranty

Little Giant Pool Cover Pumps come with a 1-year limited warranty. This means that if the pump fails due to defects in material or workmanship, Little Giant will repair or replace it free of charge within 1 year of purchase. However, this does not cover damage caused by improper use, neglect, failure to properly maintain the product according to instructions provided in the user manual, or other causes beyond Little Giant’s control.

Pool Cover Pump Not Pumping Water

If your pool cover pump isn’t pumping water, there are a few things that you can check before calling in a professional. First, make sure the power cord is properly connected to an outlet and the switch on the pump is set to “on”. If this does not resolve the issue, try cleaning out any debris or foreign particles from inside of the pump housing and ensure all hoses are securely attached with no kinks present.

Additionally, if your pump has an impeller blade that moves water through it, be sure it is free from gunk or other residue as this can prevent proper functioning.

Little Giant Pool Cover Pump Not Working


Why is My Little Giant Pump Humming But Not Working?

A humming sound from a Little Giant pump is usually caused by an electrical issue. To determine why your pump is not working, check the following:• Ensure that power is being supplied to the motor and that it has been wired correctly.

• Check for any tripped circuit breakers or blown fuses in the control panel. • Inspect the motor shaft for any obstructions, such as debris buildup or a broken impeller blade. If these steps do not resolve the issue, contact a professional electrician or local service center for further assistance.

Why is My Pool Pump Not Pumping?

The pool pump is not pumping because of one or more of the following reasons: • The power source supplying electricity to the pump may be faulty. • There could be a blockage in some part of the suction line, preventing water from entering the pump.

• Something could have gone wrong with either the impeller or motor inside the pump. All these issues can easily be diagnosed and fixed by a professional technician if necessary.

Why is My Pool Cover Not Working?

There may be several reasons why your pool cover is not working. • Check the power source and ensure it is properly plugged in. • Make sure all the straps are connected securely and that there are no tears or holes in the fabric.

• Inspect any moving parts for signs of wear, such as broken hinges or rusted screws. • Test the motor to confirm that it is functioning correctly. If none of these issues appear to be causing a problem, then you may need to replace your existing cover with a new one.

Why Does My Pool Cover Pump Keep Shutting Off?

Pool cover pumps are designed to automatically shut off when the water level in your pool reaches a certain height. This is done to prevent damage from overfilling and flooding.Reasons why your pool cover pump keeps shutting off include:

– Clogged intake filter or impeller – Check and clean any filters, as well as check for debris blocking the impeller of your pump. – Faulty float switch – Check if the float switch is operating correctly, if not, replace it with a new one. – Air trapped in suction line – If there’s air trapped between the pump and skimmer or vacuum line, this can cause the motor to shut down due to low pressure.

To fix this problem you need to purge out all air in those lines with fresh water.

Little Giant Pool Cover Pump air-lock quick fix!


In conclusion, the Little Giant Pool Cover Pump Not Working can be a frustrating problem to have. Fortunately, there are several steps that you can take to try and fix the issue. If these steps do not resolve the issue then it is likely time to replace the pump.

It may also be beneficial to look into preventative measures such as proper maintenance of your pool cover pump in order to avoid this type of problem from occurring again in the future.

Home Advisor Blog

Home Advisor Blog is a reader-supported blog. This site is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to and affiliated sites.