To get air out of an intex pool pump, you must remove the air trapped in the system by opening the air release valve and filling the pump with water. Once the water starts flowing out of the air release valve, close it.
Intex pool pumps are popular among homeowners as they are affordable and easy to install and maintain. However, one common problem with these pumps is air getting trapped inside the system, which can cause the pump to lose suction and reduce its efficiency. This issue can be easily fixed by removing the air from the pump. In this article, we will guide you through the step-by-step process of getting air out of an intex pool pump. Follow these simple instructions to keep your pool crystal clear and ready for swimming!
Credit: www.omanandson.com
Causes Of Air Trapped In Intex Pool Pump
Air trapped in your intex pool pump can cause serious problems if not fixed promptly. Having air trapped in the pump can lead to reduced water flow, poor performance, and damaged equipment. If you notice bubbles flowing through your pool’s return outlets, then it means that you have air trapped in your intex pool pump.
Here we will discuss various reasons that cause air to be trapped in the pool pump and the tools required to complete the task.
There are different reasons why air can get trapped in your intex pool pump. The most common causes include loose fittings, damaged valves, or clogged filters. In some cases, the impeller can also get damaged, which can cause air to become trapped in the pump.
Airlock and cavitation are also common causes of air trapped in the pool pump.
- Loose fittings: any fittings or connections that are not well tightened can create gaps that let the air seep in, leading to airlock.
- Damaged valves: valves that are damaged, not functioning correctly, or that are not correctly closed can let air in, leading to airlock.
- Clogged filters: clogged filters can cause a decrease in water flow, leading to cavitation or airlock.
- Damaged impellers: poor maintenance can cause impellers to wear out, crack, or chip, leading to the creation of an airlock.
- Airlock and cavitation: airlock occurs when air is trapped in the pool pump, and the water is unable to circulate correctly, leading to cavitation that eventually leads to the loss of prime.
Tools Required
Before fixing the problem of air trapped in your intex pool pump, it is crucial to have all the necessary tools close by to avoid any disruption.
- Hose clamps: used to clamp hoses to fittings.
- Teflon tape: used to seal threads to prevent leaks.
- Pipe sealing putty: used to fill gaps and seal pipe fittings.
- Screwdrivers: used to tighten or loosen fittings.
- Garden hose: used to fill the pool’s plumbing lines with water.
- Plumbers’ putty: used to create a watertight seal around jets.
Fixing the problem of air trapped in your intex pool pump can be done easily if you follow the right steps. Having all the essential tools beforehand will ensure that the task is completed without any complications. By carefully examining and identifying the cause, whether it’s a loose connection, a damaged valve, clogged filter, or a damaged impeller, you can fix the problem promptly and ensure your pool equipment operates optimally.
Steps To Get Air Out Of Intex Pool Pump
If you own an intex pool, you know how important it is to keep the pool pump working efficiently. However, due to various reasons, air might get trapped in the pool pump. This airlock can reduce the pump’s efficiency, leading to pool water that is not properly circulated, filtered or cleaned.
To remove air from the intex pool pump and fix the airlock, you must follow a step-by-step process.
Discuss The Step-By-Step Procedure To Eliminate Air From The Pool Pump
Firstly, switch off the pool pump and unplug it from the power source. Before proceeding, it is important to note that safety comes first; ensure that there is no water around the pump and that you have the necessary tools for the process.
- Locate the air release valve on the top of the filter.
- Then, unscrew the valve cap.
- Once open, air will start to escape, bubbles will flow out of the valve and water will slowly enter.
- Wait for the water to reach the top of the valve. Screw back the valve cap and tighten it firmly once the water starts to seep out of the valve.
- Restart the pool pump and check the water flow to ensure that it is normal.
Here is a summary of the above steps in bullets:
- Turn off the pump and unplug it from the power source.
- Find the valve cap on the top of the filter.
- Unscrew the valve cap and let the air release.
- Wait until water comes out of the valve and reaches the top of the valve.
- Screw the valve cap back in tightly.
- Turn on the pump and check the water flow.
It is essential to perform this maintenance regularly to ensure the smooth running of your intex pool pump and to remove any accumulated airlocks that might interfere with the pump’s efficiency. With these steps, you can quickly and effectively remove any air from your intex pool pump, allowing the pool to run properly and efficiently.
Remember to adhere to these steps strictly to prevent damage to your pool pump, and always prioritize safety when performing any maintenance on your pool equipment.
POOL FILTER PRESSURE Too High Or Too Low? Troubleshooting Tips | Swim University
Tips To Prevent Air From Getting Trapped In Intex Pool Pump
Air getting trapped in your pool pump can be a frustrating problem, especially when you’re trying to keep your pool clean and clear. Luckily, there are several tips to avoid this issue in the first place.
- check your connections: one of the most common reasons why air gets trapped in the pool pump is due to a leak in the connections. Ensure that your pump and filter are correctly connected and tightened.
- check the skimmer basket: make sure that the skimmer basket is clean and free of debris so that water can flow smoothly to the pump. If there is any blockage in the basket, then it could cause air to get trapped in the pump.
- check the water level: check the pool’s water level and ensure that it’s not too low. If the water level drops below the skimmer intake, then air can enter the pump.
- ensure proper placement: the pump needs to be positioned below the water level in the pool. If it’s above the water level, then air can seep into the pump, causing it to malfunction.
- regular maintenance: regular maintenance can help prevent air from getting trapped in the pool pump. Make sure to clean your pool’s filter, skimmer basket, and pump basket regularly, and keep an eye out for any signs of wear and tear.
Importance Of Regular Maintenance
Regular maintenance is crucial to keep your intex pool pump functioning correctly.
- ensures longevity: regular maintenance can help your pool pump last longer, ultimately saving you money in the long run. Neglecting maintenance can lead to expensive repairs or even replacement of your pool pump.
- optimizes performance: regular maintenance ensures that your intex pool pump is working optimally, with no air or debris getting trapped in the pump.
- ensures pool hygiene: regular maintenance, including cleaning the pump, filter, and skimmer basket, helps keep your pool clean and hygienic for swimming.
Preventing air from getting trapped in your pool pump requires a few measures, including checking connections, ensuring proper placement, and conducting regular maintenance. Neglecting maintenance can lead to costly repairs or replacement of your pump, ultimately causing more inconvenience. Therefore, it’s vital to implement the tips mentioned above and conduct regular maintenance to avoid the problem of air getting trapped in your intex pool pump.
Frequently Asked Questions On How To Get Air Out Of Intex Pool Pump
How Do I Know If There’S Air In My Intex Pool Pump?
Air in the pool pump can be identified by low filter pressure, poor water flow, and air bubbles in the pool.
What Causes Air In My Intex Pool Pump?
The most common reason for air in the pool pump is inadequate water levels, leaking pipes, or a malfunctioning pump lid.
How Often Should I Check For Air In My Intex Pool Pump?
It is vital to check the pool pump every couple of weeks to ensure the pump is running correctly, and the system is air-free.
How Do I Remove Air From My Intex Pool Pump?
To remove air, turn off the pump, release the air valve, remove the pump cover, and fill with water until the impeller inlet is covered.
Conclusion
To sum it up, it is important to get air out of an intex pool pump to ensure its efficiency and longevity. If you notice air bubbles in your pump, make sure to check all the joints and connections to fix any leaks.
Regular maintenance and cleaning can prevent the accumulation of air, and the use of an air release valve can help remove it easily. It is recommended to clean and replace the filter cartridge when needed, and avoid running the pump on a low water level.
By following these simple steps, you can help your intex pool pump run smoothly and effectively, and enjoy a clean and sparkling pool for longer. Remember that prevention is key, and a small effort can go a long way in maintaining your pool and its equipment.